Home / Guides

Garage Floor Epoxy Quote in Austin, TX

Get a free garage floor epoxy quote in Austin, TX: itemized prep, crack repair, coating layers and price in writing. 2-car garages from our published $1,400–$2,200 range. Call (512) 325-5434.

A garage floor epoxy quote from Austin Epoxy Flooring Pro is a free, itemized, written price for coating your garage: the preparation, the crack repairs, each coating layer, the cure schedule and the total. Our published ranges are $800–$1,200 for a one-car garage, $1,400–$2,200 for a two-car garage and $2,000–$3,200 for a three-car garage. Call or text (512) 325-5434 24 hours a day, 7 days a week, to set up a free on-site measurement, or send details through the free estimate form. This page explains how garage quotes are built, what is included, and how to judge one quote against another.

Austin Garage Floor Epoxy Price Ranges

Garage size	Published range	Typical install time
1-car garage	$800 – $1,200	1 day
2-car garage	$1,400 – $2,200	1 day
3-car garage	$2,000 – $3,200	1 day
Oversized or custom layouts	Quoted after measurement	Varies
Polyaspartic (same-day) systems	$3 – $7 per sq ft	Same day
Metallic epoxy	$6 – $12 per sq ft	1–2 days

These are the ranges published on our homepage. Your quote will land at a specific figure once we have measured the floor and checked the concrete.

What Goes Into a Garage Floor Epoxy Quote

Each line in the quote exists because it affects how the floor performs. Here is what a typical Austin garage quote itemizes.

Surface preparation

Diamond grinding opens the surface of the concrete so the coating can grip. It also removes laitance (the weak, powdery top layer), light stains and thin sealers. Edges along the walls are ground with smaller tools. The quote states that grinding is included and covers the edges.

Crack and spall repair

Most Austin garages have cracks. The quote lists how they are handled: hairline cracks filled during the base coat, wider cracks routed out and filled, and spalled or chipped areas patched. If a crack has moved so that one side is higher, the quote will say whether grinding it flush is included or whether it needs a separate repair.

Primer or moisture treatment

Where moisture is a concern, a primer designed to tolerate vapor pressure may be added. If testing shows normal readings, this line may not appear. Either way, the quote should say what was found.

Base coat

The base coat is usually a pigmented epoxy that bonds to the ground concrete and builds thickness. Its color shows through in partial-flake floors and sits under the chips in full-flake floors.

Broadcast layer

For flake floors, vinyl chips are broadcast into the wet base coat. The quote specifies full or partial broadcast and the color blend. For quartz floors, colored quartz granules are used instead.

Topcoat

The topcoat is the layer you actually walk and park on. In Austin garages this is often a polyaspartic, chosen because it cures quickly and resists yellowing in sunlight. The quote names the topcoat material and how many coats are applied.

Cleanup and walkthrough

The quote should state that the work area is cleaned up and that you get a walkthrough explaining cure times and care.

Exclusions

Common exclusions include moving stored items, coating stem walls and steps (often available as add-ons), major structural slab repairs, and work on areas outside the garage. Exclusions are listed so nothing is assumed.

How We Arrive at Your Number

The range for your garage size is the starting point. Where your quote lands depends on:

Measured area. Garages vary a lot in actual square footage.
Condition. Clean bare concrete sits toward the lower end. Old coatings, heavy staining and many repairs push it higher.
System. Partial flake costs less than full flake. A polyaspartic topcoat or a full polyaspartic system changes the material cost. Metallic is priced per square foot.
Add-ons. Stem walls, steps, a threshold strip or a custom color blend.
Access and timing. Tight access or special scheduling.

Polyaspartic vs Epoxy Garage Floor Quotes

Many people asking for a garage quote want to know whether to choose polyaspartic or epoxy. We often quote both.

An epoxy-based system (epoxy base, flake, epoxy or polyaspartic topcoat) builds a thick, strong layer and is forgiving of minor surface flaws. Cure takes longer.
A full polyaspartic system cures much faster, which means less time without your garage, and holds its color well in sunlight. It requires quick, experienced application.
A hybrid system, with an epoxy base and a polyaspartic topcoat, is the most common choice for Austin garages because it combines build with a fast-curing, color-stable top layer.

If your garage door faces west and stays open in the afternoon, or if you need to park inside again quickly, mention it. Read more in our polyaspartic vs epoxy guide for Austin garages.

Flake, Quartz and Solid-Color Garage Quotes

Finish	Look and feel	Good for	Quote notes
Full flake	Speckled, textured, hides dust	Everyday parking, family garages	Most common garage quote
Partial flake	Solid base with scattered chips	A cleaner, flatter look	Slightly less material
Quartz	Dense granules, sandpaper texture	Workshops, mudrooms, wet areas	Texture set by topcoat thickness
Solid color	Smooth, uniform	Display garages, clean workspaces	Shows imperfections more
Metallic	Glossy, flowing	Showpiece garages	Priced per sq ft

Austin Conditions That Show Up in Garage Quotes

Clay soil and cracking

East of the Balcones Fault zone, much of the Austin area sits on the dark clay soils of the Blackland Prairie. Those clays swell when wet and shrink when dry, and garage slabs crack and shift as a result. That is why crack repair is a standard line in Austin quotes rather than an occasional extra. West of the fault, slabs sit on rockier limestone ground, where cracking patterns tend to be different.

Heat

An Austin garage in July can be far hotter than the air outside. Coatings cure faster in heat and give installers less working time. We schedule installs early in the morning in hot months, and the quote assumes that timing.

Sun through the garage door

Many garages sit with the door open for hours. Ultraviolet light yellows some epoxy topcoats over time, which is why polyaspartic topcoats are so common here.

Moisture

Older slabs may lack a vapor barrier, and irrigation or poor drainage can push moisture into the concrete. Where we see signs of this, the quote includes testing and, if needed, a moisture-tolerant primer.

Garage Quotes in Austin

Austin garages range from small detached garages behind older central homes to oversized three-car garages in newer subdivisions. Older garages often have old paint, patches and wider cracks, which raise preparation time. Newer garages are often in good condition but have smooth, hard-troweled slabs that need thorough grinding. Both are quoted from an on-site look, not a guess.

Garage Quotes in Georgetown

We also quote garage floors in Georgetown. Many Georgetown homes are newer, with two- and three-car garages, and many owners want a floor that is easier to clean and less slippery. A textured flake or quartz finish with a suitable topcoat is a common request. See epoxy flooring Georgetown TX for more.

How to Get Your Garage Quote

Call or text (512) 325-5434, open 24 hours, 7 days a week.
Send photos: one wide shot and close-ups of cracks, stains or peeling.
Tell us the garage size, how you use it and the finish you want.
Book a visit for measurement and a concrete check.
Receive the written quote with every line itemized.

We respond the same day.

Calling About a Quote

We are open 24 hours, 7 days a week, so you can call or text about a garage quote whenever it suits you, whether that is before work, on a lunch break or on a Sunday afternoon while you are standing in the garage looking at the cracks.

Comparing Garage Floor Quotes

When you have more than one quote, put them side by side and check:

Is diamond grinding included, including the edges?
Are crack repairs described, not just mentioned?
Are all layers named, including the topcoat?
Is the broadcast full or partial?
Are cure times stated for foot traffic and vehicles?
Are exclusions listed?
Is the price a total, in writing?

A quote that is much lower usually leaves something out. A kit or a single thin coat over etched concrete is a very different product from a ground, multi-layer system.

Garage Uses That Change the Quote

How you use the garage matters as much as its size.

Parking only. The focus is hot tire resistance, drips and the door threshold.
Workshop. Dropped tools, rolling cabinets and solvents call for a thicker build and a chemical-resistant topcoat.
Home gym. Heavy weights are usually paired with rubber mats, and the quote can treat matted areas differently.
Storage and laundry. Moisture from washers and stored items against walls make edge treatment and stem walls more important.
Car hobby or detailing. Water, soaps and polishes are used often, so a textured finish and an easy-clean topcoat help.

Tell us which of these describes your garage, even if it's a mix. It helps us quote the right system the first time instead of revising it later.

Optional Add-Ons You Can Ask to Have Quoted

Some items are left off a basic garage quote because not everyone wants them. Ask if you'd like any of these priced:

Stem walls. The short concrete walls around the edge of many garages. Coating them gives a finished, wraparound look and makes the base of the walls easier to clean.
Steps and landings. The step up into the house takes a lot of foot traffic and is often the first place a bare floor looks worn.
Garage door threshold. The strip under the door sees water, grit and sun. It can be included in the main floor or treated separately.
Custom flake blends. Standard blends are quoted by default; custom mixes may change the material cost.
Additional topcoat. An extra clear coat adds thickness and can soften the texture of a full-flake floor.
Texture additives. A slip-resistant additive in the topcoat helps on floors that get wet often.
Adjacent areas. Laundry rooms, mudrooms, storage rooms or a back patio can be quoted at the same visit.

What Installation Day Usually Looks Like

For a typical two-car garage, the day runs roughly like this:

Early morning arrival. In warm months we start early so the slab is as cool as possible.
Protection and setup. Walls, doors and nearby items are protected from dust and coating.
Grinding. The floor and edges are ground, with dust collected by vacuum.
Repairs. Cracks and spalls are filled and ground flush.
Base coat and broadcast. The base coat is rolled out and chips or quartz are broadcast while it is wet.
Scrape and clean. Once the base has set, loose chips are scraped and vacuumed.
Topcoat. The clear topcoat seals the floor.
Walkthrough. We explain when you can walk on the floor and when you can drive on it.

Times vary with the system, the weather and the condition of the slab, but this is the shape of most one-day garage installs.

Questions People Ask After Getting a Quote

"Why is my quote near the top of the range?" Usually because of preparation: an old coating to remove, heavy oil staining or many repairs. Ask us to point to the line items that moved the price.

"Can I lower the price?" Choosing partial flake instead of full flake, skipping stem walls, or clearing the garage yourself can help. We won't remove grinding or the topcoat, because those protect the result.

"Can I do part of the garage now and the rest later?" It's possible, but seams between separate installs are visible. Doing the whole floor at once looks better and usually costs less per square foot.

"What if it rains?" Interior garage work isn't usually affected by light rain, but very high humidity or a cold front can change the schedule. We'll let you know ahead of time.

Preparing Your Garage for Installation

Once you accept the quote, you'll need to:

Move cars, stored items and anything on the floor out of the garage.
Take down or lift items mounted low on the walls if they block the edges.
Plan to keep vehicles out until the stated cure time has passed.
Make arrangements for pets and children to stay out of the area during work and curing.

We'll confirm all of this in writing before the install date.

Caring for the Finished Floor

A coated garage floor needs little care. Sweep or use a dust mop regularly, clean spills promptly, and wash with a mild cleaner and water. Avoid harsh solvents unless we've confirmed the system can handle them. Placing mats under car tires in winter helps keep road grit off the surface. Hot tires can mark some coatings, so the topcoat choice in your quote takes this into account.

What a Garage Quote Can't Tell You

A quote can describe the work and the materials, but some things can't be promised in advance: exactly how long a coating will last on a particular slab, whether a repaired crack will reopen if the soil moves, or how future moisture will behave. We'd rather tell you that plainly than make a claim no one can back up.

Customer Feedback

Austin Epoxy Flooring Pro has a 5.0 rating on Google. If we have coated your garage, a short review describing the floor and the process helps other Austin homeowners decide.

Request a Free Estimate

Call or text (512) 325-5434 (open 24 hours, 7 days a week) or use the free estimate form. Send the approximate square footage, how the space is used, photos of the current concrete, and your timing.

Frequently Asked Questions

How much does garage floor epoxy cost in Austin TX?

Our published ranges are $800–$1,200 for a one-car garage, $1,400–$2,200 for a two-car garage and $2,000–$3,200 for a three-car garage. The written quote sets the exact price after we see the floor.

Is the garage floor quote free?

Yes. The visit and the written, itemized quote are free, with no obligation.

What is included in the quote?

Grinding, crack and spall repair, any primer needed, base coat, flake or quartz broadcast if chosen, topcoat, cleanup, cure times and exclusions.

How soon will I hear back?

We are open 24 hours, 7 days a week, and we respond the same day.

Should I choose polyaspartic or epoxy for my garage?

Many Austin garages use an epoxy base with a polyaspartic topcoat. We can quote epoxy, polyaspartic and hybrid options side by side.

How long does installation take?

Most one-, two- and three-car garages are installed in one day, with cure time before parking stated in the quote.

Do you quote garages outside Austin?

We take on projects in Austin and Georgetown.

Can you quote from photos?

Photos help us give a rough idea within our published ranges, but a firm quote follows an on-site look at the concrete.